Full Throttle Concrete

Concrete cutting in Palm Bay FL - clean cuts so only the damaged section comes out

Got a cracked or lifted section of driveway or patio? We saw it out on straight lines and haul it off, so the rest can stay.

Concrete cutting in Palm Bay, FL

We come out to look

Full Throttle Concrete has been in business since 2021 and is based in Palm Bay. When you call about a cut, we come out, look at the slab with you and talk through where the lines should go.

Licensed and insured, and easy to check

Palm Bay says any contractor you hire for work on your property must hold a state certified or registered license. We're licensed and insured, and you can check any contractor with the Department of Business and Professional Regulation at (850) 487-1395.

Straight, clean edges where new meets old

Clean edges matter to us on every job. A straight saw line gives the new concrete a clean edge to meet, so the repair looks planned instead of hacked out. Call (321) 447-2715 to set up a look.

What concrete cutting involves in Palm Bay

Concrete cutting in Palm Bay means sawing straight lines through a slab or wall, or drilling round holes for pipes, drains and conduit. It helps when part of a driveway or patio has cracked, sunk or lifted, or when a new line has to run through old concrete.

Most calls start with one bad spot, a section of driveway that cracked and sank or a patio edge that lifted and catches your toe. The first decision is where the cut lines go, because a straight cut in the right place lets us pull out the bad concrete without disturbing the slab next to it. Usually that line follows an existing control joint, one of the grooves cut so a slab cracks where it's told to.

The price moves with how thick the slab is, whether it has rebar, the steel bars inside that hold it together, whether it's a slab or a wall, how many feet of cut there are and whether you want the pieces hauled off. The schedule turns on whether the slab needs scanning first, whether the job adds digging, and what it needs for permits, which depends on the work and where your house is. You get your own figure at the estimate.

Concrete cutting, removal and the pour that follows

Cutting out cracked driveway sections

When part of a driveway has cracked or lifted, you usually don't need a whole new one. We saw along straight lines around the damage, break out the pieces and haul them off, then dig out and pack the subgrade, the dirt and base the slab sits on, before new concrete goes in. That base is the part you never see again and the first thing people want to cut from the budget. We'd rather spend there, because a soft base is usually why the old section sank.

Matching the saw to the cut

The surface and thickness of the cut decide the tool. Flat saws handle slabs like driveways and patios, wall saws ride a track along a wall, hand saws get into tight corners, and wire saws take on thick or heavily reinforced sections. Round holes come from core drilling and are priced apart from straight cuts. On structural or post-tensioned slabs, the kind with steel cables pulled tight inside, a scan for rebar, cables, conduit and pipe may be needed before any saw starts.

Pouring new concrete into the opening

A clean cut is only half the job, since the opening still needs new concrete that sits level with the slab around it. On a plain driveway we usually finish it with a broom finish, a light ridged texture that gives tires and shoes some grip when it's wet. If the cut is the start of something bigger, like opening an old slab to extend it, it can lead into concrete patio construction or a stamped concrete finish across the whole area so old and new don't look patched.

Get a price on cutting out your damaged concrete

Tell us where the cut is, whether it's a slab or a wall, about how many feet it runs and whether the pieces need hauling. We reply within one business day to set up a free in-person estimate, with no pressure to book.

(321) 447-2715

How a concrete cutting job goes

  1. Call or send the form

    Call (321) 447-2715 or use the form on this page and tell us what's cracked or lifted. We come out to look at the slab with you, mark where the cut lines should go and give you your price.

  2. Getting the slab ready

    If your job needs a permit, Palm Bay residential permits take an average of 14 working days for approval or response, and other departments have to sign off too, so plan the start date around that. Structural or post-tensioned slabs get their scan first.

  3. Cutting, removal and cleanup

    We aim to show up on schedule, cut along the marked lines, break out the pieces and keep the work area tidy as we go. If new concrete goes in, we'll tell you how long to stay off it while it cures, the days it spends hardening before it takes weight.

Concrete cutting questions in Palm Bay

How much does concrete cutting cost per foot in Palm Bay?

Saw cutting a concrete slab usually costs about $4 to $15 per linear foot across the US, and that's the market's range for the cutting itself, not our price. Reinforced or deeper slabs and wall sawing land higher per foot, and on a short cut a minimum charge can outweigh the per-foot rate.

Does a concrete cutting quote include hauling the pieces away?

Not always, because sawing concrete and removing it are separate jobs, and some cutters cut the lines and leave the pieces where they lie. When you compare quotes, ask whether each one includes taking the cut concrete away. When we replace a damaged section, we cut it out and remove it.

Do I need a permit to cut concrete in Palm Bay?

It may, and the city's list doesn't settle it, so check with the city before work starts. Palm Bay's Land Development issues permits for flat concrete work that won't carry a structure, and its list names fences, flatwork and sheds, not cutting. Starting without a permit you needed can bring a penalty of up to four times the fees.

Does someone have to call before digging out concrete in Florida?

Yes, Florida law requires whoever does the excavation or demolition to notify Sunshine State One-Call of Florida at least 2 full business days ahead. That gives utility companies time to find and mark their underground lines, so on a job that adds digging, the work starts after that window.